10 Industrial Electrical Training Video Course Library Apr 2026

Calculate expected full-load current given HP, voltage, and efficiency. Course 4: Motor Starters & Contactors Focus: Manual and magnetic starters, contactor operation, overload relays.

| Segment | Topic | Key Demo | |---------|-------|-----------| | 1 | One-line diagrams vs. wiring diagrams vs. ladder logic | Trace power from utility to motor | | 2 | Wire numbering & terminal strip labeling | Follow a wire from page 3 to page 10 | | 3 | Finding an open circuit – step-by-step voltage method | Locate a broken wire in a control loop | | 4 | Finding a short circuit – resistance method | Blown fuse investigation | | 5 | Ground fault location using a megohmmeter | Isolate a wet motor winding |

Focus: NFPA 70E, arc flash, lockout/tagout (LOTO), and hazard recognition. 10 Industrial Electrical Training Video Course Library

Using a schematic, find why a pump will not start – all indicators are off. Course 9: Electric Motor Maintenance & Failure Analysis Focus: Megger testing, bearing replacement, alignment, and winding evaluation.

Choose a fuse type for a motor circuit with high inrush current. Course 6: Control Circuits – Relays, Timers & Sensors Focus: Industrial control logic, timing relays, proximity/photo sensors, and basic ladder logic. Calculate expected full-load current given HP, voltage, and

| Segment | Topic | Key Demo | |---------|-------|-----------| | 1 | Digital multimeter (DMM) basics: V, A, Ω, continuity | Measure line voltage (120V/480V) | | 2 | Clamp meter – measuring current without breaking circuit | Measure motor FLA in a panel | | 3 | Insulation resistance tester (megohmmeter) | Test motor winding insulation | | 4 | Non-contact voltage tester & solenoid tester | Verify absence of voltage | | 5 | Understanding test lead categories (CAT III / CAT IV) | Compare meters for industrial use |

A 50 HP motor trips on overload – megger reading is 2 MΩ at 1000V. Repair or replace? Course 10: Industrial Control Panel Design & NFPA 79 Focus: Panel layout, wire bending space, grounding, and electrical standards. wiring diagrams vs

Identify correct PPE for a Category 2 arc flash hazard. Course 2: Multimeter & Electrical Test Equipment Focus: Proper use of DMMs, clamp meters, insulation testers, and voltage testers.

Identify 5 code violations in a photo of a real industrial panel. Production & Delivery Notes | Element | Recommendation | |---------|----------------| | Video length per course | 45–75 minutes (broken into 5–8 segments of 5–12 min) | | Instructor | Licensed master electrician or EET with 10+ years industrial experience | | Visual style | Split-screen: instructor + live panel / motor / VFD + animated circuit diagrams | | Hands-on materials | Each course includes a downloadable worksheet, schematic, and quiz | | Certification | Completion badge + .pdf certificate per course | | Target software playback | LMS (SCORM), YouTube Unlisted, or company training portal | Optional Add‑On (11th course – Bonus) PLC & HMI for Electricians (Basics of digital inputs/outputs, ladder logic vs. relay logic, and HMI navigation for troubleshooting.)

Troubleshoot a contactor that chatters when energized. Course 5: Overcurrent Protection – Fuses & Circuit Breakers Focus: Fuse types, breaker trip curves, selective coordination, and short-circuit ratings.

| Segment | Topic | Key Demo | |---------|-------|-----------| | 1 | Megger test procedure – phase-to-phase & phase-to-ground | Acceptable values for 480V motor | | 2 | Surge comparison test for turn-to-turn shorts | Compare good vs. bad waveform | | 3 | Motor bearing types & replacement (grease vs. oil) | Pull a bearing with a puller | | 4 | Shaft alignment – dial indicator vs. laser alignment | Demonstrate soft foot | | 5 | Analyzing failed windings – overload, single-phasing, contamination | Show 5 failed stator photos |