Parallel Data Cable (Printer extension cable, with male-female 25 pin connector, and pin to pin through)	A-A type USB cable(for power)



ATMEL89 Adapter	ATMEL PLCC 44 Adapter	TSOP 48 Adapter

FWH/HUB PLCC32Adapter	PLCC32 Adapter	SOIC Adapter(Simplified)
On-Board	On-Board
AC or DC Power Adapter (9V or 12V, 200mA)	SOIC Adapter(Professional)	
		

Fotos Viejas Japonesas Desnudas  

I hope this article meets your requirements. If you have any further requests or need assistance with a different topic, feel free to ask.

The history of photography in Japan is a rich and fascinating one, spanning over a century and a half. From the early days of studio photography to the modern era of digital imaging, Japanese photography has evolved significantly over the years. One aspect of this history that is often overlooked is the development of nude photography in Japan. In this article, we will explore the world of vintage Japanese nude photography, examining its history, evolution, and cultural significance. fotos viejas japonesas desnudas

The post-World War II period saw a significant shift in Japanese culture, including the emergence of a more liberal attitude towards nudity. This led to a surge in nude photography, with photographers such as Nobuyoshi Araki and Masahisa Fukase gaining international recognition. I hope this article meets your requirements

Today, vintage Japanese nude photography is highly sought after by collectors and historians. Many of these photographs are fragile and at risk of deterioration, making preservation a pressing concern. From the early days of studio photography to

Installation Steps


Check the parallel printer port setting in the bios, it should be EPP or Normal.
Check there are any active resident programs that use the printer port, such as TWAIN drivers. You may have to remove it.
Connect one end of the 25 pin SubD parallel cable to PCprinter port
Connect the other end of parallel cable to 25Pins port of the programmer
Connect USB power cable or AC adaptor (Note: if you are working on the EPROM programming. You may need use a AC adaptor, so that you can get Vcc 5.6V and 6.2V when doing programming)
Theyellowpower normal indicator of the programmer should light up, then the programmer power supply is normal.
Run the software
Select devices type
Click the Willem in toolbar to change to PCB3
Set the DIP switch based on the displayed pattern.

 (Note: theLPT portof PC MUSTset to ECP or ECP+EPP during BIOS setup. To enter the BIOS setting mode, you need press "Del" key or "F1" key during the computer selftest, which is the moment of computer just power up.)



Software Version To Use

The softwarecan be download fromdownload.mcumall.com

There are board hardware selection jumper on the board. When set the jumper to PCB3B, then user have to use 0.97ja and before version software.

If the board selection set to PCB3.5, PCB5.0, PCB5.5C, then the software 0.98D6 should be used.



 The softwareinterface:



fotos viejas japonesas desnudas



Hardware Check

After start the program, click test hardwar under Help menu. If the connection and power supply is normal, then appears: "Hardware present" Otherwisecheck if the programmer connects well with PC, or power supply is normal.



Jumper Configuration



PCB3.5/PCB4E

fotos viejas japonesas desnudas 
(Two PLCC32 adapter is not applied on the PCB4E)



PCB5.0

fotos viejas japonesas desnudas



PCB5.5C



fotos viejas japonesas desnudas

Note: the Vcc setting jumper only has effect when you are using AC adaptor as power source. For the USB power only 5V Vcc is available.

For the PCB5.5C, set DIP steps:

1. press DIP Set button twice to check current DIP bit position. Then set it again for ON or OFF.

2. press DIP Bit shift button to shift the DIP bit position to where need to set. And then press DIP Set button twice to check current DIP bit position. Then set it again for ON or OFF.

3. Repeat those steps till all DIP bit ae set same as software indicated.

For PCB5.5C voltage and Special chip selection:

1. Put back the safety jumper.

2. Press the voltage button and hold for 1 second, the voltage LED should move to next. Repeat till desired voltage LED light up.

3. Press the chip selectionbutton and hold for 1 second, the chip LED should move to next. Repeat till desiredLED light up.

4. Remove the safety jumper to lock the selected voltage and chip selection



DIPSwitch (PCB3.5, PCB5.0)

fotos viejas japonesas desnudas 

When programming one chip, followthe program prompt to set DIP switch.



I hope this article meets your requirements. If you have any further requests or need assistance with a different topic, feel free to ask.